26-06-2008, 10:55 AM
Laur hea inimesena ässitas baabelkala tekstile kallale. Tulemus sai sihuke:
Pin 1 to 3 can be quite exchanged or differently wired. The free pin is possibly occupied by a KFZ specific bus signal. Pin 4 and 7 are frequently (e.g. AUDI, VOLKSWAGEN and Opel) exchanged. Pin 5 is wired with newer Volkswagen models with a further permanent current supply. With re-tooling radios if this connection is not cut, one does not enjoy long the new equipment! Pin 4 (and/or 7): With some automarks (e.g. AUDI, VOLKSWAGEN) putting the ignition key in is already sufficient, in order to activate bias-reducing potential. Whether the actual current supply over continuous or switching pluses happens, depends on radio AND automakers.
B: Kõlarid kõik samamoodi
C: Muud Pin 1 to 6 are always directly wired. Only newer Becker radios use pin 6 than Subwoofer exit. The remainder is to the manufacturers at the free disposal. On some controllers can be realized LINE into entrances. -- Nüüd MT lustikummuti Becker audio APS 30: n skeem. Selline vidin sobib näiteks 210-sse kuni 06/99. Plug A * Pin 01 GAL at clamp 6 of C2 * Pin 02 K-line * Pin 03 * Pin 04 clamp 30 (continuous pluses) * Pin 05 switching exit (automatic antenna) * Pin 06 clamp 58d (light) * Pin 07 clamp 15R (ignition) * Pin 08 clamp 31 (mass) Plug B * Pin of 01 loudspeakers in the back right + * Pin of 02 loudspeakers in the back right - * Pin of 03 loudspeakers in front right + * Pin of 04 loudspeakers in front right - * Pin of 05 loudspeakers in front left + * Pin of 06 loudspeakers in front left * Pin of 07 loudspeakers in the back right + * Pin of 08 loudspeakers in the back right - Plug C (audio 10/APS 30) * Pin 01 interior CAN High * Pin 02 interior CAN Low * Pin 03 back headlight * Pin 04 Wake UP D2B at CD-Wechsler/FSE * Pin 05 + supply CD change-over switch * Pin 06 - Supply CD change-over switch
Teema jäi mulle silma seetõttu, et keegi kodanik üritas enda punnsilma paigaldada JVC lustikummutit ja see tegi Pontut (mäletate, Pontu oli peale surma vaiksem, kui haud). Ilmnes, et 210 pistikus oli just A ehk vooluosas juhtmeid ringi tõstetud. Kuna mina senini elasin teadmises, et ISO on alati ISO, tekkiski tunne, et seda üllatust võiks ka teistega jagada...
illy:
Pin 1 to 3 can be quite exchanged or differently wired. The free pin is possibly occupied by a KFZ specific bus signal. Pin 4 and 7 are frequently (e.g. AUDI, VOLKSWAGEN and Opel) exchanged. Pin 5 is wired with newer Volkswagen models with a further permanent current supply. With re-tooling radios if this connection is not cut, one does not enjoy long the new equipment! Pin 4 (and/or 7): With some automarks (e.g. AUDI, VOLKSWAGEN) putting the ignition key in is already sufficient, in order to activate bias-reducing potential. Whether the actual current supply over continuous or switching pluses happens, depends on radio AND automakers.
B: Kõlarid kõik samamoodi
C: Muud Pin 1 to 6 are always directly wired. Only newer Becker radios use pin 6 than Subwoofer exit. The remainder is to the manufacturers at the free disposal. On some controllers can be realized LINE into entrances. -- Nüüd MT lustikummuti Becker audio APS 30: n skeem. Selline vidin sobib näiteks 210-sse kuni 06/99. Plug A * Pin 01 GAL at clamp 6 of C2 * Pin 02 K-line * Pin 03 * Pin 04 clamp 30 (continuous pluses) * Pin 05 switching exit (automatic antenna) * Pin 06 clamp 58d (light) * Pin 07 clamp 15R (ignition) * Pin 08 clamp 31 (mass) Plug B * Pin of 01 loudspeakers in the back right + * Pin of 02 loudspeakers in the back right - * Pin of 03 loudspeakers in front right + * Pin of 04 loudspeakers in front right - * Pin of 05 loudspeakers in front left + * Pin of 06 loudspeakers in front left * Pin of 07 loudspeakers in the back right + * Pin of 08 loudspeakers in the back right - Plug C (audio 10/APS 30) * Pin 01 interior CAN High * Pin 02 interior CAN Low * Pin 03 back headlight * Pin 04 Wake UP D2B at CD-Wechsler/FSE * Pin 05 + supply CD change-over switch * Pin 06 - Supply CD change-over switch
Teema jäi mulle silma seetõttu, et keegi kodanik üritas enda punnsilma paigaldada JVC lustikummutit ja see tegi Pontut (mäletate, Pontu oli peale surma vaiksem, kui haud). Ilmnes, et 210 pistikus oli just A ehk vooluosas juhtmeid ringi tõstetud. Kuna mina senini elasin teadmises, et ISO on alati ISO, tekkiski tunne, et seda üllatust võiks ka teistega jagada...
illy: